电话
  1. 首页
  2. > 新闻中心
  3. >箱式碎石机结构原理赏析,优势太明显

箱式碎石机结构原理赏析,优势太明显

发布时间:2021-03-17

箱式碎石机简介

箱式碎石机主要适用于抗压强度在中等硬度以下的各种物料的一、二级破碎。广泛用于矿山、建材、化工、冶金行业各种脆性材料的破碎。适用于石灰石、青石、页岩、煤矸石、白亚、石膏、明矾、砖、瓦等。其物料的抗压强度不超过300兆帕,湿度不大于30%。

The box-type rock crusher is mainly suitable for the primary and secondary crushing of various materials with compressive strength below medium hardness. It is widely used in the crushing of various brittle materials in mining, building materials, chemical and metallurgical industries. Suitable for limestone, bluestone, shale, coal gangue, white Asia, gypsum, alum, brick, tile, etc. The compressive strength of the material does not exceed 300 MPa, and the humidity does not exceed 30%.

箱式碎石机高清大图

箱式碎石机厂家生产车间

箱式碎石机厂家生产车间

箱式碎石机一次成型,效率高

箱式碎石机一次成型,效率高

小型箱式碎石机,价格实惠

小型箱式碎石机,价格实惠

箱式碎石机结构组成

箱式碎石机主要由:箱体、蓖条、转子、锤头(板锤)、破碎板、衬板等组成,机架部分为三分体结构,只须打开破碎机后部机壳,即可进行更换板锤、破碎板、衬板等检修维护作业。箱式碎石机零部件的互换性强,易损件品种少,便于备件的采购和管理。箱式破碎机的驱动系统采用电动机+机械联轴器+V型皮带+破碎机的方式,能改善电机启动性能,使电机能平稳启动运行。皮带传动方式可起到双重的过载保护的功能,驱动系统所要求的电机功率低,大大降低运行成本。此驱动方案是经济实用、性能优良、安全可靠的驱动方案。

The box-type rock crusher is mainly composed of: box body, grate bar, rotor, hammer head (blade hammer), crushing board, lining board, etc. The frame part is a three-part structure, only need to open the rear of the crusher The casing can be repaired and maintained such as replacing the hammer, broken plate, and lining board. The box-type rock crusher has strong interchangeability of parts and fewer varieties of wearing parts, which is convenient for the purchase and management of spare parts. The drive system of the box crusher adopts a motor + mechanical coupling + V-belt + crusher, which can improve the starting performance of the motor and enable the motor to start and run smoothly. The belt drive mode can play a double overload protection function, and the motor power required by the drive system is low, which greatly reduces the operating cost. This drive scheme is economical, practical, high-performance, safe and reliable.

箱式碎石机工作原理

箱式破碎机生产线的石料由机器上部直落入高速旋转的转盘,在高速离心力的作用下,产生高速度的撞击与高密度的粉碎,石料在互相打击后,又会在转盘和机壳之间形成涡流运动而造成多次的互相打击、摩擦、粉碎、直至粉碎成所要求的粒度。

The stones of the box crusher production line fall directly from the upper part of the machine into the high-speed rotating turntable. Under the action of high-speed centrifugal force, high-speed impact and high-density crushing are produced. After the stones hit each other, they will be on the turntable and The vortex motion is formed between the casings, causing multiple blows, frictions, crushing, and crushing to the required particle size.

箱式碎石机优势

1、进料粒度大、破碎比大、处理后的颗粒粒度均匀。

2、成品率高,颗粒状产品占85%左右,完全符合使用要求。

3、箱式碎石机锤轴安装可调,锤头寿命长。

4、可以用栅格进行产品粒度的控制,方便使用,颗粒形状好。

5、箱式碎石机机箱可翻转,检修更方便。

6、具有整形功能,使产品成立方状、堆积密度大,保护机身。

7、产量高、性能稳定。

8、粗、中碎一步到位,工艺流程简化。

1. The feed size is large, the crushing ratio is large, and the particle size after treatment is uniform.

2. The finished product rate is high, and granular products account for about 85%, which fully meets the requirements of use.

3. The installation of the hammer shaft of the box-type rock crusher is adjustable and the hammer head has a long life.

4. The grid can be used to control the particle size of the product, which is convenient to use and has a good particle shape.

5. The case of the box-type rock crusher can be turned over, making maintenance more convenient.

6. It has a shaping function to make the product square, with a large accumulation density, and protect the fuselage.

7. High output and stable performance.

8. Coarse and medium crushing can be done in one step, and the process flow is simplified.

返回顶部
右侧悬浮